Car lifts are essential equipment for modern vehicle repair and maintenance. Their proper operation is directly related to work efficiency and personnel safety. This article systematically explains the standard operating procedures for car lifts, covering key aspects such as pre-use preparation, operating procedures, precautions, and emergency procedures, aiming to provide professional guidance for operators.
I. Pre-use Preparation
Before starting a car lift, the following basic inspections must be completed:
1. Equipment Visual Inspection: Verify that the lift platform is free of deformation, cracks, or hydraulic oil leaks, and that steel structure connectors (such as pins and bolts) are not loose.
2. Hydraulic System Inspection: Check that the hydraulic oil level is within the calibration range (usually between the scale lines on the side of the tank) and that the oil is clear and free of impurities. If the oil level is insufficient, refill with the same type of hydraulic oil. If the oil is severely contaminated, completely replace it and clean the tank.
3. Electrical System Verification: Verify that the power supply voltage is consistent with the rated voltage of the equipment (typically 380V three-phase), that cables are not damaged or aged, and that the grounding device is securely connected. Test the control panel buttons (up, down, and emergency stop) for sensitivity.
4. Support Structure Alignment: For scissor lifts, check the lubrication of the scissor arm hinge points; for column lifts, ensure the guide rails are free of obstructions and the guide wheels rotate freely.
II. Standard Operating Procedures
(I) Vehicle Parking and Securing
1. Slowly drive the vehicle to be lifted into the center of the lift platform, ensuring the tires are aligned with the platform stoppers (if any) to prevent uneven loading and lift imbalance.
2. Adjust the wheel chock position according to the vehicle model. Use dedicated wheel chocks to secure the front wheels (or drive wheels) to prevent the vehicle from sliding during lifting. For manual transmission vehicles, it is recommended to shift the vehicle into P gear and apply the parking brake. For automatic transmission vehicles, additional wheel chocks should be used after shifting into P gear.
(II) Lifting Operation
1. The operator stands at the control panel on the side of the lift (do not stand directly under or in front of the platform). After confirming that the vehicle is secure, press the "Up" button.
2. Maintain a consistent lifting speed. Initially (approximately 30 cm off the ground), pause for 3-5 seconds to observe whether the vehicle is stable and not tilting. If any abnormality is detected (such as noticeable sinking on one side), immediately press the "Emergency Stop" button and investigate the cause.
3. Once the vehicle has been raised to the target height (typically 40-80 cm off the ground for repair work, and higher for chassis inspections), pause again and confirm stability before proceeding.
(III) Lowering Operations
1. After repairs are completed, remove all tools and wheel chocks and ensure that no personnel are present near the platform.
2. Press the "Lower" button and control the lowering speed to a slow and steady pace. When approaching the ground (approximately 10 cm off the ground), make minor adjustments to ensure the platform is completely flush with the ground before fully releasing the button.
III. Key Considerations
1. Load Limits: Strictly adhere to the maximum load indicated on the equipment nameplate (e.g., 2 tons, 3 tons, etc.). Overloading is strictly prohibited. For multi-wheeled vehicles, calculate the total weight (including passengers and tools) to avoid approaching critical values.
2. Environmental Requirements: Avoid operating in rain, snow, high temperatures (over 40°C), or low temperatures (below -10°C). Extreme temperatures may cause abnormal hydraulic oil viscosity, affecting equipment performance.
3. Regular Maintenance: Clean the platform surface for oil and dirt after each shift. Check the hydraulic oil filter and remove impurities monthly. Have a professional technician perform a comprehensive inspection of the wire rope (if installed), chain, and safety locking device every six months.
IV. Emergency Procedures
In the event of a sudden malfunction (such as uncontrolled descent of the lift, unusual noise, or oil leakage):
1. Immediately press the red "Emergency Stop" button to shut off the power supply and notify nearby personnel to evacuate the danger zone via the intercom or loudly call.
2. If the lift is suspended in mid-air, do not climb on it or attempt to repair it yourself. Use the manual pressure relief valve (equipped on some models) to slowly lower the lift to a safe position.
3. After the fault is corrected, the equipment must be re-adjusted by a manufacturer-authorized technician. The cause of the fault and the corrective action must be recorded and archived for future reference.
Proper operation of a car lift is fundamental to ensuring safe and efficient maintenance operations. Operators must undergo professional training and pass assessments before taking up their posts. During daily operations, operators must remain vigilant and strictly adhere to operating procedures. Scientific management and proper use can maximize the life of the equipment and prevent accidents.










